16-04-2021



What an absolutely idiotic idea to preserve them with this useless.ecm crap. THey even admit it has no purpose because Windows and OS X easily can deal with the compressed image file without this ecm junk.

(Second) ECM Swap
  • At the same time, ECM is also a small application that offers you the possibility to perform the conversion in no time. ECM is able to work with popular CD image files, such as BIN, CCD, CDI, CDR, ISO or NRG. To import these CD images you can simply drag and drop the files on top of the ECM main window or you can use the entries in main File menu.
  • Simple GUI tool to convert ECM files to BIN seamlessly In Linux Resources. CC0-1.0 License Releases 1.
  • File Converter Ecm To Bin free download - All File to All File Converter 3000, Wise Video Converter, File Shredder, and many more programs.
The ECM that came in 1986-1989 TPI Fbody's and Vettes is a series 1227165 (165). The ECM is located up and behind the dash, on the passenger side of the car. (Behind where a Glove Box would be in a older pre 80s car)

The '85 and '86-'89 TPI cars use a MAF sensor inline of the intake air flow to precisely measure the air flow and adjust A/F, etc. based on that reading. 1990-1992 TPI cars switched over to a MAP system (also referred to as Speed Density) where the ECM gets a estimated air flow based on engine vacuum. The change to MAP is rumored to be based on cost reasons for GM, but for performance engine builders, the limited air flow able to pass thru the MAF is also a consideration of changing to a MAP system.

I wanted to be able to quantitatively compare the MAF-vs-MAP systems on my vehicle to have a better understand the limits of each and how my car would react/benefit from both. To easily switch between the two systems, I set out to build/adapt both ECMs, different sensors, and wiring harness differences in a convenient manner to make switching back and forth between them as simple/easy as possible. After working thru the wiring diagrams and getting much valued help from the GMECM mailing list, I came up with a solution to equip my car with both set of sensors that are different, and build an adaptor cable between my existing ECM harness ('165 wired) and the newer ('730) ECM.

Note that you do not have to build the adaptor to change systems, you caneasily reuse your MAF wiring and existing knock sensor engine wiring to hook thenew MAP and knock sensor to. This is a more permanent solution if you'resold on Speed Density and don't want to switch back-forth between the MAF and MAP systems like I do.

86 ECM pinout diagram Osx
92 Sensor/ECM wiring page1, page2, page3, page4, page5, page6, page7,

This is a text file that has the required connector pin changes for theconversion. They are listed in order of the '165 connector pins as wellas in order of the '730 connector pins. (Note that you need an additionalECM connector for the '730 ECM)

The pin naming nomenclature is shown in the above pinout/wiring diagrams.

'165 ECM connector pin changes for 92 ECM

Many thanks go out to:
Don BroadusConvert
John Gwynne
Bruce Plecan
Dave Zug
Parts needed:
  • MAP Sensor
  • new Knock Sensor (If you want to reuse your '165 KS, check HERE )
  • '730 ECM
  • V8 MEMCAL for '730 ( I used the AUJP base, GM part# 16151348 for$39 online at http://www.gmpartsdirect.com .
  • (EPROM programmer w/WINBin and 730 ECU file (or equivilent) for {min} Mag. VSS change and VATS disable. See Programming101 doc for PROM tuning guide)
  • This is a current copy of my 730 ECU !


    A handy tool for repining GM harness connectors is the Lisle Terminal Tool, P/N 14900 and can be found here

    Adaptor parts needed:

  • old ECM or new ECM pin header
  • old harness or two for (1)24 pin and (2)32 pin harness connectors
  • Cinch Crimp on pins from D-shell connectors (Cinch P/N 030-1953-000) available from http://www.newark.com .

    Total cost for the project is ~ $150 depending on what you can get thrusalvage yards and what you have to purchase new..

    Click on any image below for an enlargement (~500K) image.January/February 2000 (Preparation)
    MAF harness plug -to- MAP sensor engine harness The MAF plug was made by cutting apart an old broken MAF and soldering wires to the pins. The MAP plug is available in most any Auto Store in the 'HELP!' section.


    All three (24,32 and 32) connectors modified and slipped onto header
    Long taped-off wires in foreground will hook to new MAP and Knock Sensors.


    All three (24,32 and 32) connectors modified and slipped onto header
    Long taped-off wires in foreground will hook to new MAP and Knock Sensors.


    '730 ECM pluged into harness.
    (labeled, but not soldered to pin header)


    '730 and '165 MEMCALs.
    '730 (lower) from L4 Cav, '165 from v8.

    Convert Ecm To Bin Osx


    '730 V8 MEMCAL.
    Knock Sensor circuit board built onto MEMCAL.


    '730 (and '165) modified V8 MEMCAL.
    low-profile ZIF into solded socket.


    '92 5.7L Knock Sensor from Autozone


    'Trailer Hitch'
    wiring harness pulled thru firewall for MAP hookup to adaptor cable

    ALL DONE!


    MAP and second knock sensor wired into engine-bay and down/thru firewall
    Black plastic conduit used for all wiring for clean look.

    I started the car and gathered an initial ALDL scan to check sensors,etc. The car ran very poorly and the data showed it running VERY rich with the stock '92 5.7l calibration. I have enough preliminary data to start zoning in the EPROM. The ALDL data (after warmup) from the RPMs, MAP, O2 from the first start can be seen here
    The adaptor was then unhooked and the '165 ECM reattached to prove they can be swapped easily. The ALDL data from the subsequent MAF is shown here .

    A basic EPROM image and road test data will be forthcoming..


    3-1/2' aluminum tube replacing MAF sensor
    Cut from 3-1/2' diameter aluminum jar, 6' long. Painted 'stealth' black


    3-1/2' aluminum tube replacing MAF sensor
    Cut from 3-1/2' diameter aluminum jar, 6' long. Painted 'stealth' black
    MAF hookup wire can be seen on thermostat housing

    Convert Ecm To Bin Osx Download

    The first test of the season was run at Cecil County Dragway on March 4, 2000. The 7 runs were recorded as:

    1 (MAP) 13.098@105 (let car shift to OD)
    2 (MAP) 13.095@105 (let car shift to OD)
    3 (MAF) 12.941@105 (kept car in 3rd to 5600rpm)
    4 (MAF) 13.071@103 (let car shift to OD)
    5 (MAF) 12.927@106 (kept car in 3rd to 5800rpm)
    6 (MAP) 13.063@105 (kept car in 3rd to 5800rpm)
    7 (MAP) 13.050@105 (kept car in 3rd to 5600rpm)

    *note: all the runs had 60' times between 1.812 and 1.860 and so I feel are warranted for comparison..

    Convert Ecm File To Bin

    The Bins used for the tests are a AUJP (Runs 1,2) , AUJP (Run 6) , AUJP (Run 7) variant used in the '730, and a ARAP variant used in the '165.

    Diacom snapshots of the RPM,air flow,O2 for the best MAP and MAF runs..

    Diacom snapshots of the RPM,Spark Adv (TDC relative),Knock retard for the best MAP and MAF runs..

    00-5-21
    The MAP system runs very strong now. The above tests were with an early(in tuning) MAP chip that barely had the fueling stable and had no sparkadvance tuning done. I've since tuned it much better and the MAP setup isrunning at and above the level of the MAF setup.. Bin

    Gm Ecm Bin Files


    Convert Ecm To Bin Osx Format

    I will soon bebuilding a cold-air intake for it that is much more difficult to do witha MAF system...

    Convert Ecm To Iso

    NameBIN
    Full nameBIN, Generic Binary File
    File extension.bin
    MIME typeapplication/x-binary
    Developed byWindows, Macintosh
    Type of formatSystem
    DescriptionBIN (Binary files) is a non-text computer file. Data is encoded with binary code instead of text for storage and processing. Some of the coding can be translated or interpreted into text while the rest is for formatting and other useful functional features. Older Microsoft Word documents work in binary. The BIN file extension often refers to CD disk images. Binary data can be translated into plain text to prevent the code from trying to execute functions. This allows the sending, receiving, and downloading of BIN files. Hex editors are very useful for viewing of binary sequences but text editors can be used as well.
    Technical detailsFiles with the BIN extension usually look like junk when viewed directly with a text editor. Without knowledge of which portion of ASCII code is crucial for the file or which program to open the file in, the files are not very useful. These files often contain executable code and data programs that are required by various OS’s for the starting of a program. Binary digits (bits) are grouped in 8-character groups and used to interpret something other than numbers and letters by different programs. This allows images, text, sound, and other files (compressed) to be found in a BIN file. Headers can contain metadata used by the program to interpret data and identify format.
    Associated programsAVG, CDRWin, Linux
    Wiki https://en.wikipedia.org/wiki/Binary_file